Home » Posts tagged 'Chickasha French Drain Installation'
Tag Archives: Chickasha French Drain Installation
Our customer had a back porch Sun Room. Every time he had a hard rain, Water would run in one door and out the other. An indoor creek across his Sun Room.
We installed a French Drain in front of the South Door. It was 26 feet long and ran from a gutter downspout which it was connected to, in front of the South Door and along the house covering the entire “Low” Area. Then we connected 4 inch ADS Solid Drain pipe to the French Drain and ran down hill around the corner of the house to the street.
Once the 4 inch solid drain pipe was connected to the French Drain and the two gutter down spouts, a pop-up emitter was installed to release the water at the street.
The next step was to cover the drain pipe with dirt and put the sod back in place on top of the pipe. There was about 8 wheelbarrows of dirt left over that was displaced by the drain pipe and the French Drain. The extra dirt was scooped up and hauled away.
While installing the drainage system, it was necessary to move two sprinkler heads that were in the way of the drain pipe installation. This was no problem. Installing drainage systems and French drains for folks who have a sprinkler system is very common. Moving Sprinkler heads or pipes sometimes is necessary. We always leave the sprinkler system in complete working order and we discuss any changes in the sprinkler system with the customer before we do it to make sure that everyone is on the same page. In most cases the customer cant tell that we made any changes to the sprinkler system at all.
Oklahoma Drainage and Sprinkler Repair 405 203 9419
We Install Drainage Systems to fit various needs for home owners an businesses. A Drainage System, can utilize French Drains, Surface Drains, Channel Drains or Sump Pumps as the intake part to the Drainage System. The Drain or Sump Pump brings water into the Drain Pipe. The Drain pipe takes the water to the ” Exit.” Which is Either a “Curb Outlet” or a “ Pop Up Emitter.”
The Three parts of A Drainage System are: THE INTAKE ( French Drain or Surface Drain ) etc. The TRANSITION ( The Drain Pipe ) which can be many sizes or type. The EXIT ( A Curb Outlet or Pop Up Emitter )
The Drainage part of our company name means that we solve water problems for people in Oklahoma. Heavy rain is becoming more common. Back in 1993 when I first started, a hard rain was considered to be about an Inch per/hour. It was fairly rare but not too uncommon. Today things are different. A weather report of rain fall at or above 4 inches per/hour was not uncommon in 2019. Excess water causes all types of damage to property both residential and commercial.
Our Drainage Systems drain water away from places you don’t want it to be. You might have water standing along the foundation of your house, or inside your basement. You might have water on your driveway or flowerbed too.
When I talk to a potential customer while doing a Drainage System estimate, I take a lot of things into consideration. First I have the Customer show me where water is standing or where it is going that it shouldn’t. This is part of defining the specific problem area. Sometimes the Water Problem Area is larger and more involved than the customer realizes. Once the Water Problem Area is clearly defined, the next step is to determine how the water is getting to the problem area. Many times there is more than one Water Source to the Water Problem area. A big mistake in Drainage System Design is to stop once the most obvious Water Source is found. A Drainage System Designer must be a detective to some degree. For Example: Water running down the hill and onto the back patio might be the most obvious water source. Sub-surface water or a neighbor’s new gutter downspout could also be contributing. Most of the time water gets into the problem area from more than one source.
Next you must decide where to take the water. This is determining an Exit Point for the Drainage System. If possible you want your exit point to be down hill from the problem area. If it is up hill in all directions from the problem area, then the only solution is a Sump Pump.
Once an exit Point is determined, you must ask yourself if there is any way to install two exit points. Usually this can only work when an exit point can work on both ends of a Drainage System. The benefit of two Exit Points in a Drainage System is it greatly increases the water capacity for the Drainage System. It can move much more water faster during a heavy rain than a system with just one Exit Point. Most Drainage Systems can only utilize one Exit Point. In 21 years of Drainage System Installation, I would say 10% of our Drainage Systems have two Exit Points.
Next we have to decide what type of drain to install in the problem area. If it is a small area with one water source, Usually a Surface Drain is best. If the water problem area is large with one or several water sources, a French Drain is usually installed.
If you have several problem drainage areas you must use larger Drain Pipe if you want to connect them together to one exit point. Large French Drains should have their own exit point without attaching other Surface Drains or Gutters to them. It is very common to connect too many drains or gutters into a Drainage System. A hard rain can overwhelm the Drainage Systems Water Flow Capacity. When that happens, water backs up and the problem area floods.
I just shake my head when I see 3 French Drains and 5 gutters connected into one exit drain pipe. I see this type of design all the time. Why spend money for a Drainage System that won’t work? Lots of Cheap Builders and Fly-By-Night Drainage Companies cut corners on Drainage Systems and French Drains on new home construction.
For a French Drain or a Surface Drain or any type of Drainage System, If in doubt, use a larger Drain Pipe. Four Inch Drain Pipe is the most common. Six inch Drain Pipe is always better. If you are going to connect a French Drain and Surface Drain together, use 6 inch Drain Pipe.
Lawton Oklahoma French Drain Installation, Servicing Duncan, Altus, Chickasha, Weatherford, Elk City
Hey, Oklahoma! We are expanding our service area to include Lawton , Duncan, and Altus. If you live in Lawton and need French Drain installation, or if you live in Duncan and need a surface drain installed in your driveway, give us a call.
Oklahoma Drainage and Sprinkler Repair has been diagnosing and solving Drainage Problems since 1993. Water has the ability to get into places around your home where you really don’t want it to be. Some drainage problems are easy to solve. Typically water enters the problem drainage area one way from one source. The really tricky drainage problems occur when water enters the problem drainage area from multiple directions and from multiple sources. Sometimes a secondary water source can’t be seen or identified until the primary water problem source is eliminated.
An example of this occurs when water is running into a problem area in an obvious way over the ground where you can see it.
A drainage system is installed with a surface drain as the “intake” with drainage pipe running to an exit point. Initially the water drains away and everything looks great. The next day water is back and is all around the surface drain, but below the edge and it hasn’t rained at all, so no additional water ran over the surface of the ground to flood the area. The primary water source was solved, ( The surface water run off ) but the secondary water source was not. Which was sub-surface water, (ground water) running into the area. A surface drain can’t drain “ground water.” A French Drain should have initially been installed instead of a Surface Drain. A French Drain can drain both Surface Water and Ground Water.
Oklahoma Drainage and Sprinkler Repair Services all of Central Oklahoma including: Norman, Moore, Edmond, Yukon, Mustang, Oklahoma City, Midwest City, Del City, Blanchard, Newcastle, Purcell and Chickasha.
Standing water comes from many sources. It causes damage to sidewalks, driveways, and foundations not to mention plants, trees, and grass. Does the side of your house flood because your neighbor doesn’t have gutters, or does your sidewalk turn into a moat after a heavy rain, or worst of all, is water seeping into your foundation and duct work after a thunderstorm? Theses are just a few of the Drainage Problems that Oklahoma Drainage and Sprinkler Repair can help with. We can design a Drainage System to fit your specific needs. We install many types of Drains to solve many types of problems. French Drains, Surface Drains, Channel Drains, Basement Drains, Trench Drains, Basin Drains, and Sump Pumps are utilized.
- 4 Inch Drain Pipe Ready to be covered with dirt in Norman.
Oklahoma Drainage and Sprinkler Repair –
Hey Oklahoma, We are expanding to service all of Western Oklahoma as well as Central Oklahoma. If you live in Elk City, and need a French Drain, we can help. If water is standing on your driveway in Clinton, Give us a call. Duncan, Lawton, and Altus are all new areas of service for us.
Since 1993 Oklahoma Drainage and Sprinkler Repair has solved all types of standing water and drainage issues. We install Drainage Systems that utilize French Drains, Surface, Drains, Channel Drains, and Sump Pumps depending on the customers needs.
If you have water in a place where you don’t want it, we can help.
We also have Decades of experience repairing all types of Lawn Sprinkler Problems. Fixing broken sprinkler heads, sprinkler valve problems and controller trouble just to name a few things.
Many times people use the term ” French Drain” as general name for a Drain used in or around your home. French Drains are designed to move a lot of water over a large flooded area. They are also designed to take water in on the surface of the ground or below the surface of the ground. This is very important if the water coming into the flooded area is moving through the ground or coming up from underneath. ” Sub Surface Water Movement.” The picture below is not a French Drain!
A French Drain looks like this
A French Drain can take in water in a broad area. It can move a much larger volume of water compared to a Surface Drain. Also, it can move sub surface water moving into the area where a Surface Drain won’t move any water at all.
Surface Drains are designed to move surface water only on a smaller scale in confined areas.
Each solves specific drainage problems. A Drainage System may use one or both together or even several using many types of drains.
Do you have standing water in a large area in your yard? Typically this calls for a French Drain. A French Drain is a great way to control standing water in a large grassy area. It can also protect areas from flooding to a certain degree. As long as the French Drains capacity to move water is not exceeded. If the French Drains capacity is exceeded then water will stand in the drainage area until the rain stops and the drain has time to catch up. A good way to prevent this is to install a bigger French Drain with a larger pipe. The difference between a 3 inch French Drain and a 6 inch French Drain is huge.
Another way to beef up a French Drain is to connect gutter down spouts in front of the French Drain. The water coming off the roof causes suction in the French Drain Behind it. This greatly increases the French Drains ability to move water without increasing the size of the French Drain Pipe.
Recently we installed a French Drain inside the court yard of a rest home in Norman. We had several interesting challenges to overcome that were not typical for a French Drain Installation. The court yard was in the center of the home and was a secure area for the patrons. We had to put down painters tarps to run our wheel barrows over. We took out 44 loads of dirt and brought in 52 loads of Crushed one inch lime stone for the French Drain. Each trip was over a hundred yards from the trailer in the parking lot, in the front door, down the hall, making two turns along the way. Each time we had to be escorted by security. Needless to say, the installation of this particular drainage system took a while.In the above picture, the French Drain runs along the low area crossing all the areas where water would stand each time it rained.
When a French Drain is installed, a big mistake that is made by many people is to cover up the gravel with dirt. This is a big mistake. Basically it is ” Putting the cork back in the bottle.” If the French Drain is in full sun and has a type of grass surrounding it that spreads on its own such a ” Tift” or “Bermuda” , Grass will grow over it and the French Drain will eventually disappear. Grass covering a French Drain is a good thing if it grows across the drain without adding dirt. The Grass thatch acts a water filter preventing clogging and extending the life of the Drainage System.
When a French Drain is in Full Shade, or the surrounding grass will not spread on its own, such as with Fescue, other steps must be taken. One option is to just leave it alone. If you don’t mind how it looks, it will drain a large amount of water for many years. Many times a French Drain can be a landscaping focal point. They can be dressed up with all kinds of Rocks and Stones and Plants.
Just what is a “French Drain?” Many times people incorrectly
- A French Drain can protect your foundation!
use the phrase, “French Drain,” to apply to many different types of Drains that could be used in a Drainage System. The term is widely used and many times incorrectly connected to “Surface Drains,” or “Channel Drains.”
A Surface Drain has a grate that sits on top of a basin. The basin is underground. A Drain Pipe is connected underground to an outlet on the Drain Basin. Storm-Water Drains through the grate into the Drain Basin. Once in the Drain Basin, water travels out of the basin through a Drain Pipe. The Storm-Water continues downhill in an underground Drain Pipe to an exit point.
THIS IS NOT A FRENCH DRAIN!
A French Drain is completely different from a Surface Drain. A basic French Drain consists of a Perforated Drain Pipe in the bottom of a trench. The Drain Pipe should have a neoprene sock around the Perforated Drain Pipe. This is to ensure that the Drain Pipe does not become clogged.
The dirt that was taken out to make the trench is hauled away. It is replaced by some type of small stone or gravel depending on what is desired or available. I prefer crushed 1 inch lime stone. It is the most economical option in my area. Pea Gravel or some other type of small stone can work just as well. The lime-stone or gravel is placed in the trench on top of the perforated Drain Pipe and filled all the way to the surface (ground level). In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drain Pipe or the Gravel are installed. This helps maintain the integrity of the trench over time. It also increases the cost of the French Drain and the amount of time to install it. I install a trench liner in a French Drain about 20% of the time. Most of the time a liner in not needed.
- French Drain March 2011
French Drain Installation, Drainage Systems, Surface Drain, Sump pumps, – Oklahoma Drainage and Sprinkler Repair
Oklahoma Drainage and Sprinkler Repair, Now Servicing Duncan, Lawton, Chickasha and Altus
We have serviced all of Central Oklahoma Since 1993. Now Oklahoma Drainage and Sprinkler Repair is expanding its operations to include Western Oklahoma as well.
Hard rain and flooding seem to be more common all the time. When I started this business in 1993, having over an inch of rainfall in an hour was pretty extreme. Now having over 4 inch an hour rainfall is not unheard of and is becoming more common.
Protecting our homes and businesses from unwanted water should be a goal for all of us.
Oklahoma Drainage and Sprinkler Repair has seen and dealt with virtually every possible Drainage and Standing water problem that can occur in or around your home. With over 2000 Drainage Systems installed since 1993, we have amassed a great deal of experience. This is help full in seeing underlying problems and secondary issues that may be hard to see at first for the ” Untrained Eye.” This allows us to get things right the first time. In this business EXPERIENCE TRULY COUNTS!
Hiring your brother in law to put in your Drainage System or French Drain is as bad as hiring a Lawn mowing company that does landscaping and drains too? Water can cause a huge amount of damage. How important is your money and your home?
Blane Callen, 405 203 9419
French Drain Installation has been an area of focus for Oklahoma Drainage and Sprinkler Repair for the past 26 years. During that time we have installed over 2000 French Drains in Central and Western Oklahoma . A French Drain is one of several types of Drains that can make – up a Drainage System. French Drains are intended to move large amounts of water away from a Problem Drainage Area. Water may be standing in that area, flowing across the area on the surface, or flowing across the area below ground or “Sub Surface.” A French Drain can remove Standing Water, Water Flow at ground level, or water flow below ground level. (Surface Drains can’t do this!)
A French Drain many is used to move water away from or protect foundations. A French Drain will move both Surface Water and Sub Surface water away from a buildings foundation to an Exit Point where the water can be released without doing damage.
French Drain Installation this week was a little more difficult than normal. Many times the route that a Perforated French Drain Pipe must travel to its exit point is not very easy from an installation point of view. French Drains may have to travel through tree roots, (big ones) under sidewalks, through retaining walls, around swing sets or dog kennels or Mom’s Prize Rose Bush. The 4 inch French Drain we installed this week was in Oklahoma City south of 23rd in an old part of town where all the houses were old 2 or 3 story homes with lots of huge Elm Trees. The Elm Tree in Question actually was just an old stump that had been topped out but not completely removed. They left the roots just for us! The roots were growing into the homes foundation and were right in the way of the path of the French Drain. Forty feet of solid Elm Roots and 4 chain-saw blades later We were successful in running a new French Drain through a tree stump. Yuck! “Well you gotta do what you gotta do!”
Hard rain in Oklahoma is common. Many homes and businesses have drainage problems. Standing water from storm water run-off can cause damage to grass, trees and shrubs, not to mention foundations, sidewalks and driveways. Oklahoma Drainage and Sprinkler Repair can design and install a drainage system that may be complex using several types of drains, or basic using just a French Drain or a Surface Drain. It depends on the customer’s needs.
Today was a good day! We installed a Channel Drain in Norman. Channel Drains are a big part of our business. It takes a lot of attention to detail. Channel Drain installation takes several specific steps. It is a slow process that takes confidence and experience. I was able to train a couple of our guys on the complete process. They learned a lot but are nowhere near ready to solo yet.
If you live in Central Oklahoma and need a French Drain to protect your home’s foundation, Give us a call. A French Drain is a great way to keep water away from cement such as a home foundation or driveway. When water is left standing near a driveway or sidewalk, it can cause deterioration and cracking. A French Drain is a Good way to keep water away from problem drainage areas. We also install Surface Drains of most types and sizes depending on our customer’s needs.
Oklahoma Drainage and Sprinkler Repair can schedule a free estimate for a drainage system. A French Drain can be an important part of a Drainage System. A Drainage System is one or several types of drains connected to an exit point, were the unwanted water is to be released. A French Drain may be connected to a Surface Drain which in turn may be connected to a gutter down-spout, or Channel Drain. All the different drains are connected under ground by drain pipe to a Pop-Up Emitter or a Curb fitting to release the water.
What goes into a Drainage System depends on the individual Drainage Problem. Some Drainage Problems are Simple and need only one type of Drain Connected to an exit point. Other Drainage problems require a more complex solution.